MakerBot Replicator Z18 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach 3D-Drucker MakerBot Replicator Z18 herunter. MakerBot Replicator Z18 Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken

Inhaltsverzeichnis

Seite 2 - TABLE OF CONTENTS

WELCOME.10ABOUT THE MAKERBOT REPLICATOR Z18The MakerBot Replicator Z18 makes solid, three-dimensional objects out of melted MakerBotPLA Filament. Fir

Seite 3 - Let’s get started

WELCOME.11ABOUT THE MAKERBOT REPLICATOR Z181MAKERBOT REPLICATOR DIAGRAMS4. Control panel5. Filament drawer1. Build plate2. Filament waste bin3. Build

Seite 4 - WELCOME

WELCOME.12ABOUT THE MAKERBOT REPLICATOR Z1821MAKERBOT REPLICATOR DIAGRAMS343. USB port1. Power switch2. Power input port 4. Ethernet port

Seite 5

WELCOME.13ABOUT THE MAKERBOT REPLICATOR Z1821MAKERBOT REPLICATOR DIAGRAMS44. Bellows1. Gantry2. Extruder carriage3. Filament guide tube3

Seite 6

GETTING STARTED When you set up your MakerBot® Replicator® Z18 3D printer, remember that it was built and packaged very carefully at the MakerBot fact

Seite 7 - SAFETY AND COMPLIANCE

GETTING STARTED15ACCESSORY CHECKLISTPOWER CORDBUILD PLATE TAPE USB CABLE 5 MM HEX WRENCHSAFETY BOOKLET MAKERBOT REPLICATOR SMART EXTRUDERLARGE MAKERB

Seite 8

GETTING STARTED162 REMOVE PACKAGING MATERIALSUNPACKING THE MAKERBOT REPLICATOR Z18Cut the straps holding the MakerBotReplicator Z18 box in place and

Seite 9

GETTING STARTED173 REMOVE ACCESSORIESUNPACKING THE MAKERBOT REPLICATOR Z18Take the accessory and filament boxes out of the MakerBot Replicator Z18 and

Seite 10 - WELCOME.10

GETTING STARTED185 ADJUST LEVELING FEETUNPACKING THE MAKERBOT REPLICATOR Z18If the MakerBot Replicator Z18 shows any tendency to wobble, stabilize it

Seite 11 - WELCOME.11

GETTING STARTED19UNPACKING THE MAKERBOT REPLICATOR Z186 REMOVE LIDUse a tool to unlock the lid of the MakerBot Replicator Z18. Pull the lid o and se

Seite 12 - 3. USB port1. Power switch

1 WELCOME 04 Legal 05 Safety and Compliance 07 About the MakerBot Replicator Z18 102 GETTING STARTED 14 Accessory Checklist 15 Unpacking

Seite 13 - 3. Filament guide tube

GETTING STARTED207 REMOVE GANTRY CLIPSUNPACKING THE MAKERBOT REPLICATOR Z18Remove the orange plastic clips from the top compartment of the MakerBot R

Seite 14 - GETTING STARTED

GETTING STARTED21SETTING UP THE MAKERBOT REPLICATOR Z18Locate and unwrap the Smart Extruder and press it against the back of the extruder carriage, wi

Seite 15 - ACCESSORY CHECKLIST

GETTING STARTED22SETTING UP THE MAKERBOT REPLICATOR Z183 ROUTE FILAMENT3a. Detach the free end of the filament from the spool and insert it into the h

Seite 16 - GETTING STARTED16

GETTING STARTED234a. The build plate on the MakerBot Replicator Z18 has two parts: a removable plastic top plate, and a flat, sturdy aluminum base. Tur

Seite 17 - GETTING STARTED17

GETTING STARTED24SETTING UP THE MAKERBOT REPLICATOR Z185a. Make sure the power switch is in the O position.5b. Locate the power cord and plug it in

Seite 18 - GETTING STARTED18

STARTUPThe first time you turn on your MakerBot® Replicator® Z18 3D Printer, it will run a setup assistant that will introduce you to the control panel

Seite 19 - 6 REMOVE LID

STARTUP26THE MAKERBOT REPLICATOR Z18 CONTROL PANELThe MakerBot Replicator Z18 is operated by means of a control panel at the lower right of the 3D pri

Seite 20 - 7 REMOVE GANTRY CLIPS

STARTUP27Your MakerBot Replicator Z18 uses 1.75 mm diameter PLA filament to create 3D printed objects. Once your spool of MakerBot PLA Filament is load

Seite 21

STARTUP28FIRST STEPSOnce you’ve loaded filament into your Smart Extruder, you’re ready to print something. The LCD panel will display the test prints w

Seite 22 - GETTING STARTED22

STARTUP29FIRST STEPSCONNECT TO YOUR COMPUTERThere are four ways to move files from your computer to your MakerBot Replicator Z18: Wi-Fi, Ethernet, US

Seite 23 - GETTING STARTED23

Welcome. Let’s get started.6 TROUBLESHOOTING 53 Printing Problems 54 Leveling the Build Plate 57 Updating Firmware 59 Emptying the Filament

Seite 24 - GETTING STARTED24

MAKERBOT DESKTOPMakerBot® Desktop is a free app for preparing 3D prints and managing your 3D content. Whether you print directly to the MakerBot Repli

Seite 25

MAKERBOT DESKTOP31DOWNLOADING AND INSTALLING MAKERBOT DESKTOP1. Open a browser session and go to makerbot.com/desktop. Click the Download button.2. Se

Seite 26 - STARTUP26

MAKERBOT DESKTOP325. Select how you will connect your MakerBot Replicator Z18 to your computer. If you will print only via USB drive, clickSkip. You

Seite 27 - FIRST STEPS

MAKERBOT DESKTOP33PRINTING FROM MAKERBOT DESKTOPHOW IT WORKSMakerBot Desktop consists of four sections: Explore, Library, Prepare and Store.Explore gi

Seite 28

MAKERBOT DESKTOP34PRINTING FROM MAKERBOT DESKTOPFINDING A 3D MODELEvery 3D print starts with a 3D model. If you design a 3D model yourself, export it

Seite 29

MAKERBOT DESKTOP35PREPARING TO PRINTYou should now see your model or models at the center of a gray rectangle. This is MakerBot Desktop’s representati

Seite 30 - MAKERBOT DESKTOP

MAKERBOT DESKTOP364. Move• • Click the Move button or press the M key to go into Move mode.• • In Move mode, click and drag with your mouse to mov

Seite 31 - MAKERBOT DESKTOP31

MAKERBOT DESKTOP379. Add File• • Click Add File to open an Open File dialog.• • Navigate to the location of any STL, OBJ, or Thing file and select t

Seite 32 - MAKERBOT DESKTOP32

MAKERBOT DESKTOP38PRINT SETTINGSPRINTING FROM MAKERBOT DESKTOP154623If you want to change any settings before printing, click Settings. This is where

Seite 33 - MAKERBOT DESKTOP33

MAKERBOT DESKTOP39PRINT SETTINGSPRINTING TO THE MAKERBOT REPLICATOR Z18PRINTING FROM MAKERBOT DESKTOPWhen you are ready to print, click Print to slice

Seite 34 - MAKERBOT DESKTOP34

WELCOME.Welcome to the User Manual for the MakerBot® Replicator® Z18 3D Printer. With the MakerBot Replicator Z18 you can print high-resolution, indus

Seite 35 - PREPARING TO PRINT

MAKERBOT DESKTOP40USING THE CAMERAA feed of images from the onboard camera is always available when you’re connected to your MakerBot Replicator Z18 v

Seite 36 - MAKERBOT DESKTOP36

THE CONTROL PANELThe control panel on the MakerBot® Replicator® Z18 3D Printer allows you to interact with your 3D printer. You can use it to initiate

Seite 37 - MAKERBOT DESKTOP37

THE CONTROL PANEL42HOME SCREEN1. Print: Initiate a print stored on a USB drive or internal storage, or synced from your MakerBot account.2. Filament:

Seite 38 - MAKERBOT DESKTOP38

THE CONTROL PANEL43PRINTTurn the dial to scroll through the list of available locations. Push the dial to select the location of the file you want to p

Seite 39 - MAKERBOT DESKTOP39

THE CONTROL PANEL442 START PRINT• • If you select a file from the USB drive or internal storage, the control panel will • display the file screen.

Seite 40 - MAKERBOT DESKTOP40

THE CONTROL PANEL45PRINT43214. Print Menu. Press the control panel’s Menu button to open the Print menu. The Print menu contains the following options

Seite 41 - THE CONTROL PANEL

THE CONTROL PANEL463 PRINT COMPLETEIf you are printing a file from Thingiverse, you will be prompted to share a photo. Photos shared to Thingiverse wi

Seite 42 - HOME SCREEN

THE CONTROL PANEL47Select the Filament icon to load or unload filament. To load filament:1. Use the dial to select Load filament.2. Unlock and remove th

Seite 43 - THE CONTROL PANEL43

THE CONTROL PANEL48FILAMENTTo change filament spools:1. Unload filament. 2. Open the filament drawer and rotate the spool counterclockwise to wind the fil

Seite 44 - THE CONTROL PANEL44

THE CONTROL PANEL49UTILITIESUse the Utilities menu to access plate leveling, diagnostics and other tools.Level Build PlateSelect to begin the assisted

Seite 45 - THE CONTROL PANEL45

5LEGALThe MakerBot® Replicator® Z18 3D Printer is covered by a limited warranty. For terms and conditions, see makerbot.com/legal.All information in t

Seite 46 - THE CONTROL PANEL46

THE CONTROL PANEL50UTILITIESAdditional options are available under System Tools.Home PositionSelect to move the build platform and extruder assembly t

Seite 47 - FILAMENT

THE CONTROL PANEL51SETTINGSUse the Settings menu to edit network and sharing settings and to personalize your MakerBot Replicator Z18.Network Setting

Seite 48

THE CONTROL PANEL52INFOUse the Info menu to view your 3D printer’s history and statistics.FirmwareView the version number of the firmware currently ins

Seite 49 - UTILITIES

TROUBLESHOOTINGAs you get to know your MakerBot® Replicator® Z18 3D Printer, you may run into issues with dierent parts of the printing process. Here

Seite 50

TROUBLESHOOTING54PROBLEM SOLUTIONCan’t load filament into the MakerBot Replicator Smart Extruder.Try unloading and loading again. Hold the Smart E

Seite 51 - SETTINGS

TROUBLESHOOTING55PRINTING PROBLEMSPROBLEM SOLUTIONObject peels o the build plate during printing.Make sure that thebuildplate tape is clean and se

Seite 52 - THE CONTROL PANEL52

TROUBLESHOOTING56PROBLEM SOLUTIONThe Smart Extruder is installed, but the MakerBot Replicator Z18 does not recognize it.Remove the Smart Extruder an

Seite 53 - TROUBLESHOOTING

TROUBLESHOOTING57LEVELING THE BUILD PLATEThe build plate on your MakerBot Replicator Z18 is leveled at the MakerBot Factory and locked into place, but

Seite 54 - PRINTING PROBLEMS

TROUBLESHOOTING58LEVELING THE BUILD PLATE4. Follow the directions on the control panel. The Makerbot Replicator Z18 will move the Smart Extruder to d

Seite 55

TROUBLESHOOTING59UPDATING FIRMWAREFirmware is the soware that runs on your MakerBot Replicator Z18. Keeping your firmware up to date will help ensure

Seite 56

6LEGALMakerBot does not warrant the accuracy or completeness of the information, products, or services provided by or through this Manual and assumes

Seite 58

REFERENCE61SPECIFICATIONSPRINTINGPrint Technology: Fused deposition modelingBuild Volume: 30.5 L X 30.5 W X 45.7 H cm[12.0 L X 12.0 W X 18.0 H

Seite 59 - UPDATING FIRMWARE

REFERENCE62GLOSSARYBACK BUTTON: The button at the top right corner of the control panel’s LCD screen. The back button will oen allow you to return to

Seite 60 - REFERENCE

REFERENCE63GLOSSARYFIRMWARE: The soware that runs on your MakerBot Replicator Z18.GANTRY: The apparatus that allows the extruder assembly to move aro

Seite 61 - SPECIFICATIONS

REFERENCE64GLOSSARYPROFILE: The settings used to slice your 3D model and create a print file. MakerBot Desktop Soware comes with preset profiles for Lo

Seite 62 - GLOSSARY

REFERENCE65HOW TO USE MAKERBOT SUPPORTAt MakerBot, we take pride in oering expert, responsive, friendly customer support to customers around the worl

Seite 63

REFERENCE66CONTACTSupport makerbot.com/supportOur website has extensive documentation and troubleshooting information about your MakerBot Replicator Z

Seite 64

MakerBot One MetroTech Center, 21st Floor, Brooklyn, NY [email protected] makerbot.com

Seite 65 - HOW TO USE MAKERBOT SUPPORT

WELCOME.7SAFETY AND COMPLIANCERadio and Television InterferenceThis equipment has been tested and found to comply with the limits for a Class B digita

Seite 66 - REFERENCE66

WELCOME.8SAFETY AND COMPLIANCESafety alert symbols precede each safety message in this manual. These symbols indicate potential safety hazards that co

Seite 67

WELCOME.9Caution: The socket outlet must be located near the machine and must be easily accessible.Caution: In case of emergency disconnect the Maker

Kommentare zu diesen Handbüchern

Keine Kommentare